I read so much false information on pinball related sites when it comes to technical electronic information. Even on sites such as Pinwiki and Pinside there is usually about 50% to 70% misinformation. These people state these false facts with such authority. I worry about the people who believe it. (But hey, this is the internet. You have to take everything you read with a grain of salt.)
I should start a regular feature here called False Facts.
Today’s false fact: Diodes are connected to flipper coils to help them release faster.
Actually, it’s just the opposite. The flippers would release faster if the diodes were removed. I’ll explain why in a second. But first, don’t even think about removing your diodes to improve flipper response.
The diodes are there to suppress the voltage that is generated when the magnetic field of the coil collapses, after the power is removed from the coil. This applies to coils that are powered by a DC voltage, which would be all solid state machines and a few of the later EM machines.
OK. So here is the slow motion version of what’s happening. You press the flipper button and power is applied to the coil. Actually there are two windings in the coil, one strong one for “pull-in”, and a weaker one for “hold”, but just pretend for this discussion there is only one. In most machines, the flipper button is in the ground circuit of the coil. The power supply voltage passes through the coil, through the switch, to ground. The magnetic field builds up and pulls in the plunger. This takes a little bit of time, maybe 20-50 milliseconds (I’ve never measured it on a flipper coil).
(This is simplified. Usually there is also a relay involved to keep the flippers off when the machine isn’t playing a game. And the Williams Fliptronic system adds quite a bit more complexity to the scenario. I’m going to omit the phase relationships between voltage and current. I’m also going to refer to current flow from positive to negative.)
A regular diode allows the current to flow in only one direction, like a one-way check valve. When the coil is energized, there is no current flow through the diode because the current is going in the opposite direction for which the diode is installed. If you were to turn the diode around, all of the current would flow through the diode and not the coil, causing a short and likely burning up the diode. So at this point the diode is invisible to the coil.
As long as current is flowing though the coil, a magnetic field is maintained. When you release the flipper button, power is removed from the coil. But due to a variety of factors, including the plunger being inside the coil, it takes a little bit of time for that magnetic field to collapse. As the magnetic field collapses, it generates a current in the coil in the opposite direction that was used to create the magnetic field. So for a brief time, the current starts running backwards. Since it’s now going in the opposite direction, it goes though the diode to the other side of the coil causing a momentary short across the coil. This short dissipates the power until the magnetic field is gone and the plunger is released. But the point is, for a brief time, there is still current flowing in the circuit, through the diode, after the button is released and a magnetic field is still holding the plunger.
If the diode was removed, the magnetic field collapses, but there is no current flow because there is open circuit and no place for the electrons to go. Instead the voltage keeps rising and rising across the coil until it arcs across the switch contacts or sends a big voltage spike into the rest of the pinball machine. (This is basically how sparks are created across spark plugs in your automobile engine.)
But since there is no current flow (very little anyway) the magnetic field goes away faster and the plunger releases faster. But as mentioned, the downside is a voltage spike, which can cause havoc in a solid state machine.
So that is why the diodes are installed across every coil in the pinball machine, to reduce the voltage spikes.
There are no diodes in EM machines because they are running on AC instead of DC. The voltage is lower to begin with and the coils not as strong, there isn’t much of a spike. But it could be suppressed with a resistor and capacitor across every coil (called a snubber).
Now… there is a way to decrease the release time of flippers, but I’ve not tried it. And I’m not sure how noticeable it would be and don’t recommend it. Replace each regular diode with two zener diodes in series, back to back (opposite polarity). The diodes would need to be rated at the maximum voltage seen by the flipper coils (about 70V for a 50V system) and a current rating of 2-3 amps. A voltage spike will still be generated, but it will be a bit more controlled and may still cause havoc with a solid state machine. This is how fuel injectors in an engine are handled (essentially a coil and a plunger, just like a flipper) and those are switching on and off at a very rapid rate.